FAQ
For any customized connector, please provide the OD of each section on cable per below drawing and the impedance.

To meet cable specification, RD bespokes it with modified mandril and ferrule with the right OD and ID to terminate the specified cable with the most suitable dieset on hand tool.
For any other electrical, mechanical or environmental requirements for below, please advise in advance.
Your inquiry should specify the following, as applicable:
- Connector Interface or Series
- VSWR Requirements
- Insertion Loss
- Finish Requirements
- Hermeticity
- Mounting Method
- Frequency Range
- Specific Material Needs
- Mechanical Requirements
- Application
- Cable Requirements
- Back End Configuration

This is an appliance for holding things together tightly by means of a screw.
In coaxial connectors this screw is called the Clamp Nut, which can be tightened or reattached if needed. This design in some ways is a much better way since you can actually reattach it but then again may be insufficient since it requires some extra time.

This is a method in making joints in electrical installations. Crimping is commonly used for rapid but lasting electrical connectors. Because it can be a cold-working technique, crimping can also be used to form a strong bond between the work-piece and a non-metallic component.

The Edge Mount: It provides the best overall board to connector electrical transition and launches the connector interface parallel to the PCB giving the lowest overall height profile.

PCB Mount: Connectors can be attached to the PCB Board through-hole mounting which can make the connector permanently attached.

End Launch: It can be applied for space-limited application.
The connectors are available for varying PCB thickness and with round or flat contacts.

Surface mount technology (SMT) is a method for constructing electronic circuits in which the components (SMC, or Surface Mounted Components) are mounted directly onto the surface of printed circuit boards (PCBs). Electronic devices so made are called surface-mount devices or SMDs.

STRAIGHT: Used to connect cable to a jack mounted on equipment or attached to a cable. This is the most reliable and universally accepted type of connector style in terminating coaxial cable since it is cheaper but still offers best electrical performance.

RIGHT ANGLE: To avoid bending the cable, this kind of connector will be best fitted to ensure that it will reach tight space in which straight connectors is impossible to mate. Using this R/A type of connector will avoid having failures in the cable.

BULKHEAD: This is a different mounting style of connectors. Bulkhead connectors are designed to be inserted into a panel cutout from the front or the rear of the panel, and typically secured with a jam nut. For thick panel, this kind of mounting style of connector will be best choice. This kind of connector terminates the cable braid; feeds the cable insulator and center conductor through a panel, using a single mounting hole.

MIM is the acronym for Metal Injection Molding. It is an advanced metallurgical technology that integrates thermoplastic injection molding and conventional powder metallurgy technologies.
MIM is unique in that it realizes the mass production of complex three-dimensional objects with higher precision, greater design freedom and lower production cost.
As a relatively new technology, MIM brings about several benefits for metal forming.
- High degree of freedom for sizes and shape complexities
- Shortened product development cycles, eliminating or minimizing secondary machining operations
- Improved dimension precision
- Higher density through minimizing porosity
- Homogeneous distribution of chemical compositions
- Improve tensile strength
- Increase thermal conductivity
- Competitive pricing
Semi-rigid cables offers the best shielding performance above any other cable assemblies.
This type of cable assembly bent or shaped with no electrical degradation according to customers specification. To assure proper installation into the applicable equipment we make steps in forming or bending of the raw stock which is normally straight into desired shape of configuration.
Semi-rigid cable has an outer jacket (conductor) and a center conductor, separated by a Teflon-type dielectric. During the forming, the cable must be supported and the bend made preferably in a single motion to prevent deformation of the outer jacket.


Outer diameter: 0.03mm~200mm
Inner diameter: 0.15mm~50mm

0.5mm~600mm is our capable length range, the length and tolerance usually depends on the outer and inner diameter of machined parts.
The Company executes orders to the Customer’s exact requirements, and does not substitute one Product for another unless instructed to do so, or unless the Product has been superseded. Subject to stock availability, the Customer may place orders for any quantity.
Coax-RF shall use all reasonable endeavors to ship on or before any promised delivery date or within any delivery periods agreed.
Normally the standard items should be available in 35 days.
A). The prices are not valid for the partial shipment, unless it’s remarked in quotation.
For smaller or larger quantity, please contact us.
B). Small orders for our standard items are most welcome.
The delivery may be short when it’s in stock.
However, there has a handling charge has to be billed for the following:
- Total amount below US$1, 000 via Express Courier or Post Office is US$30.00 Switch to FOB Terms.
- Total amount below US$1,500 via air freight is US$50, T.B.A. if excessing,
- Total amount below US$3,000 via sea freight is USS150, T.B.A. if excessing.
- All banking charges outside Taiwan including the postage charges are for account of customer.
※A copy of Certificate of Origin has to be billed US$10.
※Please be noted that the validity of quotation is 4 weeks.
※Coax-RF reserves the right to adjust the prices are invalid.
T/T in advance or against irrevocable L/C
Cancellations or part cancellations of an order by the Customer can only be accepted after prior negotiation and agreement to terms which will indemnify the Company against any expense incurred.
In the event of part cancellation the Company reserves the right to invoice for any difference in selling price applicable to the quantity dispatched up to the time of cancellation.
Sales will provide beneficiary bank information before order placing.
For small order, Paypal is alternative. Sales will send a hyper link to activate a transaction.
General Packaging Standard for Cable Assembly (Bulk Packed)
- All cables are bundled by film in 50 or 100 pcs unless customer has any special requirement.
- A white sticker in 3” × 2” with cable description, bar code, place of origin is printed.
- All cables are packed with a export carton to protect it for transportation.
Note:
- Coax-RF reserves the right to pack it with less quantity once the connectors or cables is larger than normal.
- Any specific requirement on packaging, please point it out at your RFQ.
- For RF connectors, what we quote is for commercial grade and indoor usage.
※If there’s any special requirement, it should be specified at your RFQ.
※Meanwhile, it’s not included any testing unless it’s requested as it has additional cost to reflect the cost for material and other concerns.
The main benefit of T + R is the customer preference for automating connector assembly in the production process using existing assembly machines.
This in turn enables them to reduce the cost of the whole manufacturing process.
In addition to that, the connectors are protected during transportation and processing.
Our Tape + Reel packaging meets international standards EIA 481 and DIN IEC 286-3.
The fully automated packaging machine provides perfect packaging quality.
| Item | Material |
|---|---|
| Reel | Polystyrene (PS) |
| Carrier Tape | Polystyrene (PS) or Polycarbonate (PC) |
| Cover Tape | Polystyrene (PS) or PET |
Anti-static specifications are indicated for the relevant materials.
No returns will be accepted without written authorization from Coax-RF’s Return Material Authority (RMA).
Customers are asked to provide the reason for the intended return, invoice number, P/O and part number, date code/shipment date and instruction for the replacement shipment once the return has been proceeded by us.
Ownership of the product remains the purchaser’s until received by Coax-RF.
Freight is the responsibility of the purchaser.
Coax-RF warrants our parts to be free of defects in material and workmanship under normal conditions within a year of shipment. We will repair or replace any defective parts under warranty period at our discretion.
This warranty does not apply to parts that have been abused, modified, dissected, or subjected to conditions exceeding our specifications.
You may choose transportations by land, by air, or by sea according to the size and the weight of the goods.
We suggest our customers to choose transportation by express when their goods are light weighted. For good more than 100 kgs, if they are not in a hurry, they may consider transportation by sea. For more details, we may also inquire to your transportation agency or Coax-RF staffs for more information.
